How to Install a 10″ PVC BE well Casing SCH 40 for Maximum durability
Installing a 10” PVC BE WELL CASING SCH 40 for maximum durability is a straightforward process that can be completed in a few simple steps.
Oil tube chinese high–quality factory,Casing Pipe china Best Supplier,First, you will need to measure the area where the casing will be installed and mark the area with a pencil. Next, you will need to cut the PVC pipe to the desired Length. To do this, you will need a saw or a PVC pipe cutter. Once the pipe is cut, you will need to sand the edges of the pipe to ensure a smooth finish.
Next, you will need to attach the PVC BE WELL CASING SCH 40 to the area where it will be installed. To do this, you will need to use PVC cement. Apply the cement to the inside of the pipe and the area where it will be installed. Once the cement is applied, you will need to press the pipe firmly into place.
Finally, you will need to Seal the pipe. To do this, you will need to use a PVC primer and PVC glue. Apply the primer to the outside of the pipe and the area where it will be installed. Once the primer is applied, you will need to apply the PVC glue. Allow the glue to dry for at least 24 hours before testing the pipe for leaks.
| chemical composition, Mass Fraction (%) | ||||||||||||||
| grade | C | Mn | Mo | Cr | Ni | Cu | P | S | Si | |||||
| type | min | max | min | max | min | max | min | max | max | max | max | max | max | |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
| H40 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
| J55 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
| K55 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
| N80 | 1 | — | — | — | — | — | — | — | — | — | — | 0.03 | 0.03 | — |
| N80 | Q | — | — | — | — | — | — | — | — | — | — | 0.03 | 0.03 | — |
| R95 | — | — | 0.45 c | — | 1.9 | — | — | — | — | — | — | 0.03 | 0.03 | 0.45 |
| L80 | 1 | — | 0.43 a | — | 1.9 | — | — | — | — | 0.25 | 0.35 | 0.03 | 0.03 | 0.45 |
| L80 | 9Cr | — | 0.15 | 0.3 | 0.6 | 0.9 | 1.1 | 8 | 10 | 0.5 | 0.25 | 0.02 | 0.03 | 1 |
| L80 | 13Cr | 0.15 | 0.22 | 0.25 | 1 | — | — | 12 | 14 | 0.5 | 0.25 | 0.02 | 0.03 | 1 |
| C90 | 1 | — | 0.35 | — | 1.2 | 0.25 b | 0.85 | — | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
| T95 | 1 | — | 0.35 | — | 1.2 | 0.25 b | 0.85 | 0.4 | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
| C110 | — | — | 0.35 | — | 1.2 | 0.25 | 1 | 0.4 | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
| P110 | e | — | — | — | — | — | — | — | — | — | — | 0.030 e | 0.030 e | — |
| Q125 | 1 | — | 0.35 | 1.35 | — | 0.85 | — | 1.5 | 0.99 | — | 0.02 | 0.01 | — | |
| NOTE Elements shown shall be reported in product analysis. | ||||||||||||||
| a The carbon content for L80 may be increased up to 0.50 % maximum if the product is oil-quenched or polymer-quenched. | ||||||||||||||
| b The molybdenum content for Grade C90 Type 1 has no minimum tolerance if the Wall thickness is less than 17.78 mm. | ||||||||||||||
| c The carbon content for R95 may be increased up to 0.55 % maximum if the product is oil-quenched. | ||||||||||||||
| d The molybdenum content for T95 Type 1 may be decreased to 0.15 % minimum if the wall thickness is less than 17.78 mm. | ||||||||||||||
| e For EW Grade P110, the phosphorus content shall be 0.020 % maximum and the sulfur content 0.010 % maximum. | ||||||||||||||
By following these steps, you can ensure that your 10” PVC BE WELL CASING SCH 40 is installed correctly and will provide maximum durability.